verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ63X100-10S

The AirTAC SEJ Adjustable Cylinder SEJ63X100-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø63mm unit covers an effective stroke of 90–100mm without changing cylinders. Force is equal in both directions.

  • BoreØ63 mm
  • Nominal stroke100 mm
  • Adjust window10 mm
  • Effective stroke90–100 mm
  • Port sizePT3/8
  • CushionAdjustable, 36 mm
$117.47 $124.97Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ63 stroke, mounting and version on one page All SEJ63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ63X100-10S

The AirTAC SEJ63X100-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force remains equal in both directions at 1402 N (0.5 MPa). You can dial the retract end from 90 to 100 mm to perfectly match a mechanical stop.

This bore 63 unit uses a PT3/8 port and a Ø20 mm rod with an M16x1.5 thread. Because it carries the -S magnet, it supports CMSE reed and DMSE electronic sensors for position feedback. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends manage deceleration over a 36 mm cushion length.

Airtac SEJ Adjustable Cylinder SEJ63X100-10S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ63X100-10S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ63 mm
Nominal stroke100 mm
Adjustment window10 mm (90–100 mm)
ConfigurationDouble rod, double acting
Port sizePT3/8
Rod threadM16×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressureForce (both directions)
0.5 MPa1402 N
0.7 MPa1962 N
Max (@1.0 MPa)286 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ63X100-10S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
63Bore size in mm.
×100Nominal stroke length in mm.
-10Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ63X100-10S Is Used

precision_manufacturing

Gripper Jaw Calibration

Delivers 1962 N at 0.7 MPa to clamp aluminum castings, while the 10 mm retract window dials the exact jaw closing depth during machine commissioning.

swap_horiz

Packaging Changeover

Switches carton folding stops for different box heights. The 90-100 mm effective stroke range allows rapid mechanical adjustment without swapping hardware.

tune

Press Fit Positioning

Feeds bearings into housings with equal force both ways. The DMSE electronic sensor confirms the press depth before the rear stop screw locks the final position.

Is the Airtac SEJ Adjustable Cylinder SEJ63X100-10S the Right Cylinder?

Verify the 10 mm adjustment window covers your required end-position tolerance. If you need less thrust, the adjacent 50 mm bore provides 825 N at 0.5 MPa; stepping up to the 80 mm bore yields 2268 N at 0.5 MPa. If the retract position never changes after commissioning, a fixed-stroke SED saves cost. The adjustable air cushion only decelerates the load near stroke end; it is not a lock. For fail-safe position holding on air loss, use an external rod lock or BSED.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (10mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 10mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ63X100-10S FAQ

A stop screw on the back rod mechanically shortens the retract stroke. For this model, you can dial the retract end up to 10 mm, creating an effective stroke range of 90 to 100 mm. You lock the screw after setting the desired end position.

Because it is a double-rod cylinder, force is identical in both directions. It provides 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ63X100-10S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ63X100-10S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.