
The AirTAC SEJ Adjustable Cylinder SEJ63X100-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø63mm unit covers an effective stroke of 80–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X100-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window, yielding an effective travel range of 80 to 100mm. A rod exits both ends, ensuring the annulus area remains identical in both directions. This delivers an equal output force of 1402N at 0.5 MPa each way, preventing speed asymmetry.
Equipped with a standard magnet (-S), the cylinder supports CMSE reed and DMSE electronic sensors for precise end-position detection. The retract end is dialed in via a mechanical stop screw on the back rod, which you lock after setting the exact machine end-position. Adjustable air cushions at both ends decelerate the 30 to 800mm/s travel, while the extruded aluminum barrel omits external tie rods for a clean profile.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X100-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 20 mm (80–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20mm window to set precise 80-100mm upper die limits during sheet metal changeovers, utilizing the equal 1962N both-way force to lift and lower the tooling.
Fine-tune the 100mm stroke down to 80mm to dial in the exact touch depth of an electronic test probe, locking the back-rod stop screw once the optimal reach is found.
Verify the 20mm adjustment window covers your required end-position variance, letting you fine-tune the 80-100mm travel on the machine without swapping hardware. If you do not need variable stops, a fixed-stroke SED provides the same double-rod output in a shorter body. Sizing both ways: stepping down to a 50mm bore yields 825N at 0.5 MPa, while stepping up to an 80mm bore provides 2268N both ways.
The adjustable air cushion and mechanical stop screw decelerate motion near stroke ends but do not hold position on air loss; apply an external rod lock for fail-safe clamping. For ISO 15552 replacement matching, confirm the 63mm bore, 100mm nominal stroke, PT3/8 port, and your required mounting from the Basic, FA, LB, TC, FTC, TCM1, or TCM2 subset. The 100mm stroke is short enough to minimize rod deflection, but always use external guides to handle side loads.
Quick checklist
The model features a 20mm adjustment window on the retract end, allowing the effective stroke to be mechanically dialed down from the 100mm nominal length to 80mm. You set the exact end-position via a stop screw on the back rod and lock it in place.
Because the rod exits both ends, force is identical in both directions: 1402N at 0.5 MPa, 1962N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.