
The AirTAC SEJ Adjustable Cylinder SEJ63X100-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 50–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X100-50 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding an identical annulus area for equal force and speed in both directions. It delivers 1402 N each way at 0.5 MPa and 1962 N at 0.7 MPa.
This unit features a 50 mm retract adjustment window via a back-rod stop screw, letting you dial the effective stroke down from 100 mm to 50 mm. You lock the mechanical stop after setting your exact end position. It omits a position magnet, so no CMSE or DMSE sensors can be fitted to this SKU.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X100-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 50 mm (50–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm retract window to seat press dies accurately, leveraging the 1962 N both-way force for consistent clamping.
Adjust retract stroke on the fly to match varying carton heights without changing hardware, using the equal push and pull forces.
Fine-tune the actuator end stop during line commissioning to deflect products precisely, locking the 100 mm nominal stroke back to 50 mm.
Verify the 50 mm adjustment window covers your target end-position range; you can fine-tune the retract stroke from 50 mm up to the full 100 mm during commissioning. If you need less force, the adjacent 50 mm bore gives 825 N at 0.5 MPa; if you need more, stepping up to the 80 mm bore provides 2268 N at 0.5 MPa. If fixed end stops are acceptable, a standard SED avoids the extra length.
This plain SEJ does not hold position on air loss; the adjustable air cushion at both ends only decelerates near stroke end. For fail-safe holding, use an external rod lock. As a dimensionally interchangeable ISO 15552 cylinder, match the 63 mm bore, 100 mm stroke, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, TCM2) for direct replacement.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 50 mm. The effective stroke range is 50 to 100 mm, which you set and lock on the machine.
Because the rod exits both ends, force is identical in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.