
The AirTAC SEJ Adjustable Cylinder SEJ63X20-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø63mm unit covers an effective stroke of 0–20mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X20-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring an adjustable retract stroke. A rod exits both ends, yielding identical annulus areas for equal force and speed in both directions. The -20 window allows you to dial the retract end up to 20 mm, providing an effective stroke range of 0-20 mm for precise mechanical positioning.
The built-in -S magnet supports CMSE reed and DMSE electronic sensors for exact end-of-stroke detection. Adjustable air cushions at both ends decelerate the piston near the stroke limits, while the back-rod stop screw lets you lock the exact end position on the machine.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X20-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 20 mm |
| Adjustment window | 20 mm (0–20 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×20 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 0-20 mm retract stop to perfectly seat a 63 mm bore fitting, applying 1402 N of equal both-way force at 0.5 MPa without over-traveling.
Adjust the back-rod stop screw on the fly to accommodate different package heights on a conveyor, locking the end position precisely for each changeover.
Use the 20 mm adjustment window to test end positions on a new machine fixture, relying on the double-rod design for stable, equal-speed clamping in both directions.
This 63 mm bore model outputs 1402 N each way at 0.5 MPa. If your load requires less force, step down to the 50 mm bore for 825 N; if you need more push, step up to the 80 mm bore for 2268 N. The 20 mm adjustment window is ideal for dialing in short trial positions or matching a stop precisely without swapping hardware. If your end position never changes, a fixed-stroke SED provides the same ISO 15552 dimensions without the adjustment mechanism. Remember that the adjustable stop and air cushions decelerate the load but do not hold position on air loss; for fail-safe holding, use an external rod lock or BSED. Match your replacement by confirming the 20 mm stroke, PT3/8 port, and preferred mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The -20 designation means the retract stroke is adjustable over a 20 mm window. You can dial the effective stroke anywhere from 0 mm up to the 20 mm nominal length using the back-rod stop screw, then lock it in place.
Because the rod exits both ends, the drive force is identical in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.