
The AirTAC SE63 Standard Cylinder SE63X20 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 20mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X20 is a double-acting single-rod ISO 15552 profile cylinder featuring a 63 mm bore and a 20 mm stroke. It generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa, making it well-suited for short-travel high-thrust operations. The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush while resisting corrosion.
Field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during rapid cycling. This SKU lacks a built-in position sensor magnet, but the three-sided barrel grooves remain ready to host CMSE or DMSE switches if future automation requires position feedback.
| Model | Airtac SE63 Standard Cylinder SE63X20 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 20 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push at 0.5 MPa required to securely fold heavy corrugated carton flaps during high-speed case sealing operations.
Delivers rapid 20 mm ejection strokes to clear small stamped metal components from progressive dies without lingering in the tooling zone.
Actuates short-travel flow gates to divert filled beverage bottles between downstream packaging lanes with precise timing.
Stepping down to the 50 mm bore yields 982 N of push at 0.5 MPa, while stepping up to the 80 mm bore provides 2513 N, allowing you to scale thrust precisely for your fixture. To replace an existing ISO 15552 unit, match the 63 mm bore, 20 mm stroke, PT3/8 port, and your required mounting accessory. Because this is a standard double-acting cylinder, it cannot hold a load if air pressure is lost; if your application requires fail-safe positioning, consider the BSE rod lock variant.
Quick checklist
At 0.5 MPa, the SE63X20 outputs 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The maximum operating pressure is 1.0 MPa, where it achieves a maximum push of 318 kgf.
Yes, it is dimensionally interchangeable per ISO 15552 standards, serving as a direct replacement for other ISO 15552 profile cylinders. This specific SKU does not include a built-in magnet for position sensing, though the barrel grooves support CMSE and DMSE sensors if needed.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.