
The AirTAC SEJ Adjustable Cylinder SEJ63X200-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø63mm unit covers an effective stroke of 125–200mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X200-75S is a double-acting, double-rod ISO 15552 profile cylinder with a 75 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at about 1402 N each way at 0.5 MPa. You can dial the retract end from 125 mm up to the 200 mm nominal stroke.
A stop screw on the back rod mechanically sets the end position, which you lock down after fine-tuning. The extruded aluminum barrel omits external tie rods, and the -S magnet enables position detection with CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X200-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 200 mm |
| Adjustment window | 75 mm (125–200 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×200 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 75 mm window to fine-tune the 1962 N clamping reach on progressive stamping dies, locking the stop screw once the exact 125-200 mm closure is set.
Set precise mechanical endpoints for PC board routing fixtures, relying on the 36 mm adjustable air cushions at both ends to decelerate the 30-800 mm/s travel smoothly.
Verify the 75 mm adjustment window covers your required end-position range. If you need less force, the adjacent 50 mm bore provides 825 N at 0.5 MPa; if you need more, step up to the 80 mm bore for 2268 N at 0.5 MPa. If you never need to alter the stroke after commissioning, a fixed-stroke SED saves complexity.
This cylinder does not hold position on air loss; the adjustable air cushion and stop screw only decelerate the piston and set the mechanical end. For fail-safe holding, use an external rod lock. Ensure your ISO 15552 replacement matches the 63 mm bore, 200 mm stroke, PT3/8 port, and mounting choice. Since the 200 mm stroke is below 300 mm, side-load stress is manageable, but always align external guides with the M16x1.5 rod thread.
Quick checklist
The 75 mm adjustment window allows you to mechanically dial the retract stroke down from the 200 mm nominal maximum, giving an effective stroke range of 125-200 mm. You set the exact end position via a stop screw on the back rod and lock it in place.
Because the double-rod design provides equal annulus area both ways, output force is identical in extend and retract: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.