
The AirTAC SEJ Adjustable Cylinder SEJ63X300-100 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø63mm unit covers an effective stroke of 200–300mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X300-100 is a double-acting, double-rod ISO 15552 profile cylinder engineered for exacting stroke control. The rear rod features a mechanical stop screw, letting you dial the retract stroke back by up to 100 mm. This yields an effective working range of 200 to 300 mm, perfect for fine-tuning a machine end position without swapping hardware.
Because the rod protrudes from both covers, forces remain equal in both directions, eliminating speed discrepancies between extend and retract motions. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends decelerate the load near stroke end. This SKU lacks a magnet, meaning it will not support CMSE or DMSE position sensors out of the box.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X300-100 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 300 mm |
| Adjustment window | 100 mm (200–300 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×300 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 200-300 mm closure distance on a hydraulic press, using the 1962 N retract force to set dies against a stop during changeovers.
Adjust the retract stroke on a packaging conveyor to handle different carton lengths without changing the cylinder mounting hardware.
Fine-tune the end-of-stroke position during commissioning to perfectly align a 1402 N gripping jaw with varying part heights.
Verify that the 100 mm adjustment window comfortably spans your required positioning range. If you need less than 200 mm of travel, consider a shorter base stroke to save space. If your process demands less force, step down to the 50 mm bore, which provides 825 N both ways at 0.5 MPa. Conversely, heavier loads may require stepping up to the 80 mm bore for 2268 N at 0.5 MPa. If the exact stroke is fixed and known, a standard SED double-rod cylinder offers a simpler, shorter solution.
When replacing an ISO 15552 cylinder, match the 63 mm bore, 300 mm nominal stroke, PT3/8 port, and your mounting bracket (Basic, FA, LB, TC, FTC, TCM1, or TCM2 are supported). At 300 mm stroke, the extended rod is susceptible to bending under lateral loads; always use external guide rails to prevent side-load damage. Note that the stop screw and air cushions only set the mechanical end and decelerate motion; they do not hold position upon air loss. For fail-safe holding, an external rod lock is required.
AirtacDistr lists every SEJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sej63-adjustable-cylinder
Quick checklist
A stop screw on the rear protruding rod mechanically limits the retract stroke. You can adjust it up to 100 mm, giving an effective stroke range of 200 to 300 mm. Lock the screw after setting your exact end position.
As a double-rod cylinder, it provides equal force in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa. It is dimensionally interchangeable per ISO 15552, featuring a 63 mm bore, PT3/8 port, and a 20 mm rod.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.