
The AirTAC SEJ Adjustable Cylinder SEJ63X40-30 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø63mm unit covers an effective stroke of 10–40mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X40-30 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical extend and retract forces of 1402 N at 0.5 MPa. The retract stroke is mechanically adjustable via a back-rod stop screw over a 30 mm window, giving an effective stroke range of 10 to 40 mm.
It features a PT3/8 port, a Ø20 mm rod with an M16x1.5 thread, and field-adjustable air cushions at both ends. The extruded aluminum barrel has no external tie rods. This SKU lacks a magnet, so it does not support position sensors out of the box.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X40-30 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 40 mm |
| Adjustment window | 30 mm (10–40 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×40 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10-40mm stroke to lower a 1402N press head onto a workpiece, fine-tuning the exact crush depth without swapping cylinders.
Adjust the retract stop to match varying box heights on a conveyor, using the equal both-way force to positively push and pull the flap folder.
Commission a fluid valve test rig by tweaking the 30mm window to find the exact seal contact point, then lock the back-rod stop screw.
This 63 mm bore provides 1402 N both ways at 0.5 MPa. If your load is lighter, step down to the 50 mm bore for 825 N; if heavier, step up to the 80 mm bore for 2268 N. The 30 mm adjustment window lets you fine-tune the retract end position without changing mounting hardware.
For a fixed end position that never changes, a standard SED double-rod cylinder is enough. Note that the adjustable air cushion only decelerates the load near the end of stroke; it is not a lock. The cylinder will not hold position on air loss. For fail-safe holding, use an external rod lock. Because the stroke is short, side loads are minimal, but external guides are still recommended for heavy lateral loads.
Quick checklist
The nominal stroke is 40 mm with a 30 mm adjustment window. You can dial the retract end position anywhere from 10 mm to 40 mm. A stop screw on the back rod sets the position, which you lock after tuning.
Because the rod exits both ends, force is equal in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.