
The AirTAC SEJ Adjustable Cylinder SEJ63X50-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 0–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X50-50 is a double-acting, double-rod ISO 15552 profile cylinder with a 50 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so thrust is equal in both directions at 1402 N (0.5 MPa) and 1962 N (0.7 MPa). The retract end stop screw dials the effective stroke from 0 to 50 mm.
This 63 mm bore uses a PT3/8 port, a 20 mm rod with an M16x1.5 thread, and 36 mm adjustable air cushions at both ends. The rear rod extension increases overall length compared to a single-rod SE but allows mounting a flag or cam. This SKU has no magnet; add an S-suffix version for CMSE or DMSE sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X50-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 50 mm (0–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 0-50 mm retract window to set precise lower dies on a 1402 N pneumatic press, allowing quick tool changes without shimming.
Fine-tune the electrode contact gap during robotic spot welding commissioning, locking the back-rod stop screw once the optimal 0-50 mm position is found.
The 50 mm adjustment window covers the full 0-50 mm range, ideal for prototyping jigs or matching variable part heights without machining new stops. If your load requires less force, the 50 mm bore delivers 825 N both ways at 0.5 MPa; if you need more clamping power, step up to the 80 mm bore for 2268 N. For fixed repeatable end positions, a standard SED double-rod cylinder is sufficient.
This cylinder provides ISO 15552 dimensional interchangeability with a PT3/8 port and Basic, FA, LB, TC, FTC, TCM1, or TCM2 mountings. The adjustable air cushions decelerate loads near stroke end but do not lock position; for fail-safe holding on air loss, use an external rod lock or BSED. Since stroke is under 300 mm, side-load risks are minimal, but external guides are recommended for heavy off-center loads.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 50 mm window. The effective stroke can be dialed from 0 mm up to the nominal 50 mm, then locked in place for repeatable operation.
Because it is a double-rod cylinder, force is equal in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa. It is dimensionally interchangeable per ISO 15552, using a PT3/8 port and a 20 mm rod.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.