
The AirTAC SEJ Adjustable Cylinder SEJ63X50-50SFTC is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 0–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X50-50SFTC is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A stop screw on the rear rod lets you dial the retract end from 0 mm up to 50 mm, providing exact end-position tuning without swapping hardware.
Equipped with a magnet (-S) for CMSE or DMSE sensors, an FTC center-trunnion mount, and PT3/8 ports, this 63 mm bore unit runs at 30-800 mm/s. The extruded aluminum barrel contains no external tie rods, and field-adjustable air cushions at both ends absorb kinetic energy near stroke end. Note that the cushion and stop screw decelerate the load but do not hold position on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X50-50SFTC |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 50 mm (0–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 0-50 mm retract stop to seat bearings precisely.
Adjust the rear stop screw on the fly when switching pallet sizes. The FTC mount pivots smoothly while the double rod maintains equal speed both directions.
Use the 50 mm window to trial exact touch points on test specimens. The -S magnet pairs with DMSE sensors to confirm position without over-traveling.
This 63 mm bore delivers 1402 N both ways at 0.5 MPa. If your load is lighter, step down to the 50 mm bore (825 N); if heavier, step up to the 80 mm bore (2268 N). The 50 mm adjustment window is ideal for prototyping or matching variable part heights. For fixed-repeat cycles without end-tuning, a standard SED double-rod cylinder is sufficient. Ensure your FTC trunnion mount handles the resulting side loads. For fail-safe holding, add an external rod lock, as the air cushion is not a brake.
Quick checklist
A stop screw on the rear rod mechanically limits the retract stroke. You can dial the effective stroke anywhere from 0 mm to 50 mm, then lock it. This allows fine end-position tuning on the machine without changing the cylinder body.
Because it is a double-rod cylinder, force is equal in both directions. It provides 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.