
The AirTAC SEJ Adjustable Cylinder SEJ63X60-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø63mm unit covers an effective stroke of 30–60mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X60-30S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 30mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is equal both ways at 1402 N each way at 0.5 MPa. The retract end stop screw lets you dial the effective stroke down from 60mm to a 30mm minimum.
This extruded aluminum barrel unit includes a -S magnet for CMSE reed or DMSE electronic sensors. Field-adjustable air cushions at both ends decelerate the load near stroke end, while the M16x1.5 rod thread and PT3/8 port handle standard pneumatic flows.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X60-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 60 mm |
| Adjustment window | 30 mm (30–60 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×60 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Apply 1402 N of equal both-way force at 0.5 MPa to seat components, dialing the retract stroke from 60mm down to 30mm to find the exact calibration point.
Switch between different part heights on a conveyor by adjusting the back-rod stop screw in the 30mm window, locking the new end position without swapping hardware.
Test clamp locations on a new fixture by fine-tuning the end position up to 30mm, using the DMSE electronic sensor to verify the adjusted retract point.
Verify the 30mm adjustment window covers your positioning range. If you need less force, the 50mm bore offers 825 N both ways at 0.5 MPa; if you need more, step up to the 80mm bore providing 2268 N. If the exact end position never changes, a fixed-stroke SED avoids the adjustment mechanism. The stop screw and air cushion only set the mechanical end and decelerate motion; they do not hold position on air loss, so use an external rod lock for fail-safe holding. For ISO 15552 replacement matching, confirm the 60mm stroke, 30mm window, PT3/8 port, and your mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
The 30mm window lets you mechanically dial the retract stroke from the nominal 60mm down to a 30mm minimum effective length. You set the stop screw on the back rod and lock it for your exact end position.
Because the double-rod design yields identical annulus areas, force is equal both ways: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.