
The AirTAC SEJ Adjustable Cylinder SEJ63X65-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø63mm unit covers an effective stroke of 35–65mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X65-30S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions—specifically 1402 N each way at 0.5 MPa. An integrated magnet (-S) enables position detection with CMSE reed or DMSE electronic sensors.
The rear rod features a mechanical stop screw that lets you dial the retract stroke over a 30 mm window. This gives an effective stroke range of 35 to 65 mm, allowing you to fine-tune the exact end position directly on the machine without changing hardware. The extruded aluminum barrel omits external tie rods, and adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X65-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 65 mm |
| Adjustment window | 30 mm (35–65 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×65 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 35 to 65 mm clamping depth on a pneumatic press. The 1402 N both-way force securely holds the workpiece while the stop screw locks the final position.
Adjust the retract end to match different pallet thicknesses during line changeover.
Fine-tune the insertion depth of a bearing into a housing. The 30 mm adjustment window allows precise commissioning without machining new fixture plates.
Confirm this 30 mm adjustment window covers your required end-position range. If you need less force, the adjacent 50 mm bore provides 825 N both ways at 0.5 MPa; if you need more, stepping up to the 80 mm bore yields 2268 N. If the exact stroke is fixed and never changes, a standard SED double-rod cylinder is sufficient. For direct ISO 15552 replacement, match the 65 mm stroke, 30 mm window, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the air cushion and stop screw decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 30 mm window. For this SEJ63X65-30S model, the effective stroke range is 35 to 65 mm. You dial in the exact end position and lock it after setting.
Because it is a double-rod cylinder, force is identical in both directions. It provides 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.