
The AirTAC SEJ Adjustable Cylinder SEJ63X75-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø63mm unit covers an effective stroke of 55–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X75-20 is a double-acting, double-rod ISO 15552 profile cylinder with an adjustable retract stroke. A 20mm stop-screw window on the rear rod lets you dial the effective stroke down from 75mm to 55mm. Because a rod exits both ends, the annulus area is identical in both directions, yielding equal force of 1402 N each way at 0.5 MPa.
This extruded-aluminum barrel omits external tie rods for a clean profile. It features field-adjustable air cushions at both ends to decelerate the 30-800 mm/s travel speed. Note this SKU lacks a magnet (-S), so it cannot host CMSE or DMSE position sensors without modification.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X75-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 20 mm (55–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20mm retract window to perfectly seat a 1402 N pressing force against varying material thicknesses without swapping hardware.
Adjust the 55-75mm effective stroke on the fly to match different carton heights, utilizing the equal both-way force for reliable flap folding.
Fine-tune the end position during machine setup, using the 1962 N retract force at 0.7 MPa to secure heavy parts precisely.
Verify the 20mm adjustment window covers your end-position tuning range. If you need less force, the 50mm bore delivers 825 N both ways at 0.5 MPa; stepping up to the 80mm bore provides 2268 N. If your machine never requires stroke changes, a fixed-stroke SED saves space and cost.
This cylinder uses a PT3/8 port and M16x1.5 rod thread. Remember that the adjustable stop screw and air cushions only set the mechanical end and decelerate near stroke end—they do not hold position on air loss. For fail-safe holding, specify an external rod lock. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 20mm. For the SEJ63X75-20, the effective stroke range is 55-75mm. You lock the screw after setting your desired end position.
Because it is a double-rod cylinder, force is equal in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.