
The AirTAC SEJ Adjustable Cylinder SEJ63X75-40 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø63mm unit covers an effective stroke of 35–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X75-40 is a double-acting, double-rod ISO 15552 profile cylinder featuring a mechanically adjustable retract stroke. A stop screw on the back rod lets you dial in the end position over a 40 mm window, giving an effective stroke range of 35 to 75 mm. Because a rod exits both ends, the annulus area is identical in both directions, delivering an equal force of 1402 N each way at 0.5 MPa.
This extruded aluminum barrel design omits external tie rods for a clean profile. The rear rod can carry a cam or flag for external sequencing, and the field-adjustable air cushions at both ends provide precise deceleration over the 36 mm cushion length. This specific SKU has no magnet, so it does not support CMSE or DMSE position sensing.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X75-40 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 40 mm (35–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 35-75 mm stroke to set precise 1962 N insertion force for varying pin heights during machine commissioning.
Adjust the mechanical end position to accommodate different material thicknesses on a packaging line without swapping hardware.
Use the 1402 N equal both-way force to test actuation limits on a prototype assembly fixture before locking the stop screw.
Verify the 40 mm adjustment window covers your required end-position range. If your application needs less fine-tuning, a fixed-stroke SED cylinder is a simpler choice. For sizing, stepping down to a 50 mm bore yields 825 N at 0.5 MPa, while stepping up to an 80 mm bore provides 2268 N at 0.5 MPa. Remember that the air cushion and mechanical stop screw only set the end position and decelerate the load; they do not hold position on air loss. For fail-safe holding, use an external rod lock or a BSED variant. When replacing an ISO 15552 unit, match the 63 mm bore, 75 mm nominal stroke, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
The retract stroke can be dialed in over a 40 mm window. This makes the effective stroke range 35 to 75 mm, allowing you to fine-tune the end position on the machine without changing hardware. You lock the stop screw on the back rod after setting your desired position.
Because the rod exits both ends, force is equal in both directions. It generates 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.