
The AirTAC SEJ Adjustable Cylinder SEJ63X75-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 25–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X75-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so thrust is perfectly balanced at 1402 N each way at 0.5 MPa. You can dial the retract end from 25 mm up to the nominal 75 mm.
A stop screw on the back rod lets you mechanically shorten the retract stroke to hit an exact end position during commissioning. The extruded aluminum barrel has no external tie rods, and the field-adjustable air cushion at both ends decelerates the load near stroke end. This SKU lacks a magnet, so it carries no position sensor.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X75-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 50 mm (25–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 25-75 mm retract stop to match varying part heights on a packaging line, using the 1402 N both-way force to push loads accurately without retooling.
Fine-tune the exact end position during assembly commissioning, relying on the back-rod stop screw to set a precise 25-75 mm depth for pressing bearings.
Adjust the retract distance on the fly to route different carton sizes, with equal push and pull forces ensuring consistent diversion across the stroke.
The 50 mm adjustment window is ideal for dialing in a precise 25 to 75 mm end stop without swapping hardware. If your force needs are lighter, the 50 mm bore delivers 825 N both ways at 0.5 MPa; stepping up to the 80 mm bore provides 2268 N. A fixed-stroke SED is sufficient if you never need to alter the end position after setup. Remember that the cushion and stop screw decelerate and set the mechanical end, but they do not lock the rod; fail-safe holding requires an external rod lock. For direct ISO 15552 replacement, verify the 75 mm stroke, PT3/8 port, and your mounting choice.
Quick checklist
A stop screw on the rear rod mechanically limits the retract stroke. For this SEJ63X75-50, you can dial the effective stroke anywhere from 25 mm up to the nominal 75 mm, then lock it in place.
Because it is a double-rod cylinder, the force is identical in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.