
The AirTAC SEJ Adjustable Cylinder SEJ63X80-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø63mm unit covers an effective stroke of 70–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X80-10S is a double-acting, double-rod ISO 15552 profile cylinder with a 10 mm mechanical stroke adjuster. A rod exits both ends, yielding identical annulus areas so thrust matches retraction exactly at 1402 N each way at 0.5 MPa. You dial the retract end from 70 mm up to 80 mm to hit a precise machine stop without machining new spacers.
Because it is an extruded aluminum profile barrel, it carries no external tie rods and drops into ISO 15552 / VDMA 24562 dimensional footprints. The -S magnet enables CMSE reed or DMSE electronic position sensing, while field-adjustable air cushions at both ends decelerate the 20 mm rod over a 36 mm cushion length.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X80-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 10 mm (70–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivers 1402 N of equal both-way force to clamp machined aluminum housings, using the 10 mm retract dial to phase opposing gripper jaws perfectly without shimming.
Positions a labeling applicator over varied bottle heights; the 70-80 mm adjustable window lets operators dial the exact touch-down point on the fly.
Feeds a 20 mm double-rod stop into a stamping press to register sheet metal, relying on the 36 mm adjustable cushion to absorb impact at up to 800 mm/s.
Verify the 10 mm window covers your fine-tuning span; the effective retract range is 70-80 mm. If you need less thrust, the adjacent 50 mm bore delivers 825 N both ways at 0.5 MPa; stepping up to the 80 mm bore yields 2268 N. If you never change the end position after commissioning, a fixed-stroke SED does the same work for less. Remember the air cushion and stop screw only set the mechanical end and decelerate near stroke end—a plain SEJ will not hold position on air loss, so specify a BSED or external rod lock for fail-safe holding. For a true ISO 15552 replacement, match the 63 mm bore, 80 mm stroke, PT3/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
The 10 mm stop-screw window on the back rod lets you mechanically shorten the retract stroke from 80 mm down to 70 mm. You lock the stop screw after setting the exact end position, which is ideal for final machine commissioning.
Because the rod exits both ends, force is identical in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.