
The AirTAC SEJ Adjustable Cylinder SEJ63X80-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø63mm unit covers an effective stroke of 60–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X80-20S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical extend and retract forces—1962 N each way at 0.7 MPa. A stop screw on the back rod lets you dial the retract stroke over a 20 mm window, setting the effective travel between 60 and 80 mm for precise machine commissioning.
This 63 mm bore unit features a PT3/8 port, a Ø20 mm rod, and adjustable air cushions at both ends. The built-in magnet (-S) supports CMSE reed and DMSE electronic sensors for exact position feedback. The extruded aluminum barrel omits external tie rods, ensuring clean ISO 15552 dimensional interchangeability.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X80-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 20 mm (60–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20 mm retract window to set a precise 65 mm lower dead center on a small forming press, utilizing the 1962 N both-way force to consistently seat the workpiece.
Adjust the retract end position on the fly when switching between carton sizes, using the equal push and pull forces to cleanly index varying package heights.
Fine-tune the nozzle height during line commissioning over the 60 to 80 mm effective range, locking the back-rod stop screw once the optimal fluid deposit gap is found.
Verify the 20 mm adjustment window covers your required end-position range. If 1402 N at 0.5 MPa is excessive, step down to the 50 mm bore (825 N both ways); if you need more push, step up to the 80 mm bore (2268 N at 0.5 MPa). For fixed retract stops without the back rod, a standard SED cylinder suffices. The adjustable air cushion decelerates the load near stroke end but does not lock it—add an external rod lock for fail-safe holding. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
A mechanical stop screw on the rear rod shortens the retract stroke over a 20 mm window. You can adjust the effective stroke anywhere from 60 mm up to the nominal 80 mm, then lock the screw in place to secure the end position.
Because it is a double-rod cylinder, the force is identical in both directions. It delivers 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and reaches a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.