
The AirTAC SEJ Adjustable Cylinder SEJ63X80-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 30–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X80-50 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 1402 N each way at 0.5 MPa. The extruded aluminum barrel has no external tie rods, ensuring clean ISO 15552 dimensional interchangeability.
This unit features a 50 mm adjustable stroke window, letting you dial the retract end from 30 mm up to the nominal 80 mm. A stop screw on the back rod sets the exact end position, which you then lock in place—ideal for commissioning or matching a precise stop without changing hardware. It uses adjustable air cushions at both ends to decelerate near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X80-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 50 mm (30–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 30-80 mm retract stop to set precise forming depth on a light press, utilizing the 1402 N both-way force for consistent workpiece clamping.
Adjust the back-rod stop screw to accommodate varying product heights on a conveyor diverter without swapping out the entire cylinder hardware.
Fine-tune the exact end-of-stroke position during machine setup, locking the 50 mm window to match a hard mechanical stop precisely.
Confirm the 50 mm adjustment window covers your required positioning range. If 1402 N at 0.5 MPa is excessive, step down to the 50 mm bore (825 N both ways); if you need more push, step up to the 80 mm bore (2268 N). Choose a fixed-stroke SED if you do not need end-position tuning. For direct ISO 15552 replacement, match the 80 mm stroke, PT3/8 port, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note: this SKU lacks a magnet (-S) for CMSE or DMSE sensors. The air cushion decelerates the load but is not a lock; for fail-safe position holding on air loss, use an external rod lock or BSED.
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke. For this model, you can dial the effective stroke anywhere from 30 mm up to the nominal 80 mm, then lock it in place.
Because the rod exits both ends, the annular area is identical in both directions. It delivers 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa, equal for extend and retract.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.