verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ63X80-75S

The AirTAC SEJ Adjustable Cylinder SEJ63X80-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø63mm unit covers an effective stroke of 5–80mm without changing cylinders. Force is equal in both directions.

  • BoreØ63 mm
  • Nominal stroke80 mm
  • Adjust window75 mm
  • Effective stroke5–80 mm
  • Port sizePT3/8
  • CushionAdjustable, 36 mm
$117.47 $124.97Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ63 stroke, mounting and version on one page All SEJ63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ63X80-75S

The AirTAC SEJ63X80-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75mm adjustable stroke window. You can dial the retract end from 5mm up to the 80mm nominal stroke. Because a rod exits both ends, the annulus area is identical in both directions, yielding an equal force of 1402 N each way at 0.5 MPa.

A stop screw on the back rod lets you mechanically set the exact end position during machine commissioning without changing hardware. The extruded aluminum barrel omits external tie rods, and the -S magnet enables CMSE reed or DMSE electronic sensors for position feedback.

Airtac SEJ Adjustable Cylinder SEJ63X80-75S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ63X80-75S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ63 mm
Nominal stroke80 mm
Adjustment window75 mm (5–80 mm)
ConfigurationDouble rod, double acting
Port sizePT3/8
Rod threadM16×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressureForce (both directions)
0.5 MPa1402 N
0.7 MPa1962 N
Max (@1.0 MPa)286 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ63X80-75S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
63Bore size in mm.
×80Nominal stroke length in mm.
-75Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ63X80-75S Is Used

tune

Press Stroke Calibration

Dial in the exact 5-80mm clamping depth on a press fixture, using the 1402N both-way force to securely seat bearings without dedicated spacer rings.

swap_horiz

Part Height Changeover

Adjust the retract stop to match varying raw material heights on a conveyor line, relying on the 75mm window to switch positions rapidly.

precision_manufacturing

Trial Positioning

Probe and test exact end positions during machine commissioning, locking the back-rod stop screw once the optimal 63mm bore kinematics are found.

Is the Airtac SEJ Adjustable Cylinder SEJ63X80-75S the Right Cylinder?

This 63mm bore provides 1962 N at 0.7 MPa. If your application needs less force, step down to the 50mm bore (825 N at 0.5 MPa); for heavier loads, step up to the 80mm bore (2268 N at 0.5 MPa). If you do not need to fine-tune the end position, a fixed-stroke SED cylinder is sufficient.

When matching an ISO 15552 replacement, verify the 5-80mm adjustment window, PT3/8 port, and M16x1.5 rod thread. Remember that the adjustable air cushion only decelerates the load near stroke end; it is not a mechanical lock. For fail-safe position holding on air loss, use an external rod lock.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (75mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 75mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ63X80-75S FAQ

The 75mm adjustment window allows you to dial the retract stroke from 5mm up to the nominal 80mm, letting you fine-tune the exact end position on the machine without swapping cylinders.

Because the rod exits both ends, force is equal in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ63X80-75S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ63X80-75S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.