
The AirTAC SEJ Adjustable Cylinder SEJ63X80-75SFTC is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø63mm unit covers an effective stroke of 5–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X80-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75mm adjustable stroke window, yielding an effective stroke range of 5-80mm. A rod exits both ends, ensuring identical annulus areas so output force is equal in both directions at 1402 N each way at 0.5 MPa. The FTC mounting accessory provides a fixed front flange interface.
You dial in the retract end-position via a stop screw on the back rod, which is ideal for machine commissioning and hitting variable stop distances precisely. The extruded aluminum barrel carries no external tie rods, and the integrated -S magnet supports CMSE reed and DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X80-75SFTC |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 75 mm (5–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 5-80mm retract stop to precisely set a 1402 N pressing force on varying thickness circuit boards during machine commissioning.
Adjust the back-rod stop screw on the fly to match different carton flap heights without swapping out the entire ISO 15552 cylinder hardware.
Use the double-rod equal-force output to push a workpiece against a hard stop, fine-tuning the 5-80mm position window for exact milling datums.
Verify the 75mm adjustment window covers your required end-position variance; this model trims from 80mm down to 5mm. If you need less fine-tuning range, step down to the 50mm bore (825 N both ways at 0.5 MPa), or step up to the 80mm bore (2268 N both ways at 0.5 MPa) for heavier loads. If the position never changes after setup, a fixed-stroke SED cylinder is sufficient.
The adjustable air cushion at both ends decelerates the piston near stroke end but is not a lock; for fail-safe position holding on air loss, use an external rod lock or BSED. When matching an ISO 15552 replacement, confirm the 63mm bore, 80mm stroke, PT3/8 port, FTC mount, and magnet. Because the effective stroke can be as short as 5mm, ensure the 36mm cushion length has enough room to decelerate without bottoming out.
Quick checklist
The model has a 75mm adjustment window on the back rod. You can dial the retract end-position from a 5mm effective stroke up to the full nominal 80mm stroke, allowing exact end-position tuning on the machine without changing hardware.
Because the double-rod design yields equal annulus areas, force is identical both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.