
The AirTAC SEJ Adjustable Cylinder SEJ80X100-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø80mm unit covers an effective stroke of 0–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X100-100S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so the output force is perfectly equal in both directions at 2268 N (0.5 MPa). The rear rod stop screw lets you dial the retract stroke down from 100mm to 0mm, providing an effective stroke range of 0-100mm for exact on-machine positioning.
Equipped with a magnet for position sensing, this unit works seamlessly with CMSE reed and DMSE electronic sensors. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends decelerate the load near the end of travel. Note that the stop screw sets the mechanical end but does not hold position on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X100-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 100 mm (0–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 0-100mm retract window to set precise pressing depth for bearing fits, utilizing the 2268N both-way force to press and retract parts equally.
Adjust the stop position on the fly during line changeovers to accommodate different package heights, locking the back-rod screw exactly at the required end point.
Use the 0-100mm effective range to test multiple end positions during R&D jig commissioning before finalizing a fixed-stroke cylinder design.
Verify the 100mm adjustment window covers your required positioning range. If you need less fine-tuning, a fixed-stroke SED double-rod cylinder may be sufficient. For sizing, stepping down to a 63mm bore yields 1402 N at 0.5 MPa, while stepping up to a 100mm bore provides 3681 N both ways. When replacing an ISO 15552 cylinder, match the 80mm bore, 100mm stroke, PT3/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). For fail-safe load holding on air loss, add an external rod lock or use a BSED series cylinder.
Quick checklist
The retract stroke is adjustable over a 100mm window. You can dial the effective stroke down from 100mm to 0mm using the back-rod stop screw, then lock it in place for your exact end position.
Because the rod exits both ends, the force is identical in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.