
The AirTAC SEJ Adjustable Cylinder SEJ80X150-75 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø80mm unit covers an effective stroke of 75–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X150-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas and equal force of 2268 N each way at 0.5 MPa. You can dial the retract stroke from 75 mm up to the 150 mm nominal length using a stop screw on the back rod.
This design eliminates hardware swaps during machine commissioning. The extruded aluminum barrel omits external tie rods, and the field-adjustable air cushions at both ends decelerate the motion near stroke end. Note that this SKU lacks a magnet, so it has no CMSE or DMSE position sensing.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X150-75 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 75 mm (75–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Fine-tune the 75 mm retract window to precisely match material stop positions on a mechanical press feed line, leveraging the 2268 N both-way force.
Adjust the retract end on the fly when a packaging machine switches carton sizes, avoiding the need to physically swap out the cylinder.
Dial the clamping travel to exact part heights for robotic welding fixtures, using the equal push and pull forces to secure varied assemblies.
Confirm the 75 mm adjustment window covers your required end-position range. If you need less force, the adjacent 63 mm bore provides 1402 N both ways at 0.5 MPa; if you need more, the 100 mm bore yields 3681 N both ways. A fixed-stroke SED is sufficient if your retract position never needs tuning. This cylinder does not hold position on air loss; use a BSED or external rod lock for fail-safe holding. For an exact ISO 15552 replacement, match the 80 mm bore, 150 mm stroke, PT3/8 port, and mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke. You can dial the effective stroke down from the 150 mm nominal length to as low as 75 mm, then lock the screw in place.
Because the rod exits both ends, the force is identical in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.