
The AirTAC SEJ Adjustable Cylinder SEJ80X150-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø80mm unit covers an effective stroke of 75–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X150-75S is a double-acting, double-rod ISO 15552 profile cylinder with a 75mm adjustable retract window, allowing you to dial the effective stroke down from 150mm to 75mm. A rod exits both ends, yielding identical annulus areas. This means you get equal force and speed in both directions, delivering 2268 N each way at 0.5 MPa.
The retract end is tuned via a stop screw on the back rod—set your exact end-position on the machine, then lock it down. This -S variant includes a magnet for CMSE reed or DMSE electronic sensors. It features field-adjustable air cushions at both ends over a 36mm length to decelerate heavy loads, and uses an extruded aluminum barrel with no external tie rods.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X150-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 75 mm (75–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the retract stop in 75mm increments to match varying flange depths on a press brake, using the 2268N both-way force to move the backgauge consistently.
Fine-tune the clamp extension on a robotic welding fixture during commissioning, locking the back-rod stop screw precisely against the weldment.
Adjust the end position on a carton erector to accommodate different box heights on the fly, relying on the equal double-rod push and pull to cycle reliably.
Confirm this 75mm adjustment window covers your positioning range. If you need less fine-tune capacity, a fixed-stroke SED80 saves space. For sizing neighbors: a 63mm bore provides 1402 N both ways at 0.5 MPa, while stepping up to a 100mm bore yields 3681 N. This 80mm bore gives 2268 N at 0.5 MPa and 3175 N at 0.7 MPa, with a maximum of 463 kgf at 1.0 MPa.
When replacing an ISO 15552 unit, match the 150mm stroke, 75mm window, PT3/8 port, and M20x1.5 rod thread. The standard mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2. Note that the air cushion and stop screw only set the mechanical end and decelerate near stroke end; they do not hold position on air loss. For fail-safe holding, use an external rod lock.
Quick checklist
The retract end features a 75mm adjustment window. You can mechanically dial the effective stroke down from the nominal 150mm to a minimum of 75mm to fine-tune the machine end position, then lock the stop screw.
Because the rod exits both ends, the annulus area is identical in both directions. The force is equal both ways: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.