
The AirTAC SEJ Adjustable Cylinder SEJ80X175-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø80mm unit covers an effective stroke of 125–175mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X175-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so the drive force is equal in both directions at 2268 N each way at 0.5 MPa. By turning the stop screw on the back rod, you can dial the retract end position over a 50mm window, giving an effective stroke range of 125-175mm for precise machine commissioning.
This 80mm bore unit runs at 30-800 mm/s with a PT3/8 port and a Ø25mm rod end threaded M20x1.5. It carries field-adjustable air cushions at both ends to decelerate the load near the stroke extremes. This SKU has no internal magnet, so it will not directly host CMSE or DMSE position sensors without modification.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X175-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 175 mm |
| Adjustment window | 50 mm (125–175 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×175 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 125-175mm clamping reach on a 2268 N press to accommodate varying material thicknesses during setup.
Adjust the retract stop up to 50mm to switch flap-folding positions for different carton sizes without swapping hardware.
Fine-tune the actuator endpoint on a conveyor sorting gate to align perfectly with product flow using equal both-way force.
Verify that your end-position target falls within the 125-175mm effective stroke range to leverage the 50mm stop-screw adjustment. If you need less force, the adjacent 63mm bore provides 1402 N at 0.5 MPa both ways; if you need more, stepping up to the 100mm bore yields 3681 N at 0.5 MPa. If the exact 175mm stroke is permanently fixed and never requires changeover, a standard fixed-stroke SED cylinder is sufficient. For direct ISO 15552 replacement, match the 80mm bore, 175mm stroke, PT3/8 port, and your mounting choice from the SEJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the adjustable cushion and mechanical stop screw decelerate the load and set the end position, but they do not hold position upon air loss.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 50mm window. You can adjust the effective stroke from 125mm up to 175mm, then lock the screw in place for precise end-position tuning.
Because the double-rod design provides equal annulus area both ways, force is identical in extend and retract: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.