
The AirTAC SEJ Adjustable Cylinder SEJ80X30-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø80mm unit covers an effective stroke of 20–30mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X30-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10 mm mechanical stroke adjustment window. A stop screw on the rear rod lets you dial the retract end position, yielding an effective stroke range of 20 to 30 mm for exact machine commissioning. Because the rod exits both ends, the annular area is symmetric, delivering an equal output force of 2268 N each way at 0.5 MPa.
This extruded aluminum profile cylinder omits external tie rods for a clean ISO 15552 envelope. It features field-adjustable air cushions at both ends to decelerate the 25 mm rod near stroke limits, and the built-in magnet (-S) supports CMSE reed and DMSE electronic sensors for precise position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X30-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 30 mm |
| Adjustment window | 10 mm (20–30 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10 mm window to set a precise 20-30 mm retract stop for a stamping pin, using the 2268 N both-way force to consistently press mating hardware without re-engineering the fixture.
Adjust the rear stop screw on the fly when switching a packaging line to different carton heights, relying on the symmetric double-rod output to push and pull the folding flap equally.
Fine-tune the extend and retract endpoints during machine commissioning to perfectly land a test probe, locking the 25 mm rod mechanism after finding the optimal 20-30 mm travel.
Verify the 10 mm adjustment window provides enough travel to fine-tune your end stop within the 20-30 mm effective range. If you need less force, the adjacent 63 mm bore provides 1402 N both ways at 0.5 MPa; stepping up to the 100 mm bore yields 3681 N. If your application never requires end-position tuning, a fixed-stroke SED cylinder provides the same symmetric force more economically.
This cylinder uses a PT3/8 port and M20x1.5 rod thread. Mounting options are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2. Note that the stop screw and air cushions only set the mechanical end and decelerate motion; they do not hold position on air loss. For fail-safe holding, specify an external rod lock.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 10 mm window. For this 30 mm nominal stroke model, the effective retract distance is adjustable from 20 mm up to 30 mm. You lock the screw after setting the desired end position.
Because it is a double-rod cylinder, the force is identical in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.