
The AirTAC SEJ Adjustable Cylinder SEJ80X65-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø80mm unit covers an effective stroke of 35–65mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X65-30S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 30 mm adjustable retract window. By turning the stop screw on the back rod, you set the effective stroke anywhere from 35 to 65 mm, letting you dial in a precise end position on the machine without swapping hardware.
This 80 mm bore unit uses a PT3/8 port and a 25 mm rod with an M20x1.5 thread. It carries the -S magnet for CMSE reed or DMSE electronic sensors, and includes field-adjustable air cushions at both ends to manage deceleration over the 36 mm cushion length. The extruded aluminum barrel is dimensionally interchangeable per ISO 15552, and the rear rod can support an external cam or flag.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X65-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 65 mm |
| Adjustment window | 30 mm (35–65 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×65 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 35-65 mm retract stroke to set exact die clearance on a press, leveraging the 3175 N both-way force at 0.7 MPa to form parts consistently.
Adjust the retract stop on the fly when switching carton sizes on a packaging line, using the 30 mm window to match new flap heights without repositioning brackets.
Fine-tune the end stop for metal panel bending, using the equal both-way force and rear rod to trigger a DMSE electronic sensor at the exact 45 mm mark.
Verify the 30 mm adjustment window covers your required end-position range; here you can tune the retract stroke from 35 up to 65 mm. If you need less force, the adjacent 63 mm bore provides 1402 N at 0.5 MPa both ways, while stepping up to the 100 mm bore yields 3681 N at 0.5 MPa both ways. If your stop position never changes after commissioning, a fixed-stroke SED double-rod cylinder is sufficient. For replacing an ISO 15552 cylinder, match the 80 mm bore, 65 mm stroke, PT3/8 port, and your mounting choice from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the air cushion and stop screw decelerate the load near stroke end but do not hold position on air loss; for fail-safe holding, use an external rod lock or BSED.
Quick checklist
The 30 mm stop screw window lets you mechanically shorten the retract stroke from the nominal 65 mm down to 35 mm. You set the exact end position on the machine and lock the back rod screw in place.
Because the rod exits both ends, force is equal in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.