
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX160-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 160mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X160-75 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. By turning the rear screw, you can trim the nominal 160mm stroke back by up to 75mm, creating a highly versatile 85-160mm usable travel window for precise end-position tuning.
This adjustable stopper allows you to dial in the exact retract position during commissioning or product changeover without swapping the cylinder or adding external stops. The adjuster acts purely as a travel stop and works alongside the 27mm variable air cushions at both ends to decelerate the load; it does not hold the load without live air pressure. The extruded aluminum barrel includes sensor grooves on both sides, ready for AirTAC CMSE reed or DMSE electronic sensors if position feedback is later required.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX160-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Fine-tune the retract position within the 85-160mm window during machine commissioning or product size changes without physically replacing the cylinder.
Dial in the exact end-of-stroke location for multi-format production lines, using the 75mm adjustment range to adapt to different component sizes quickly.
Choose this 32mm bore adjustable cylinder when your application requires variable end stops or frequent setup changes, stepping down from a 40mm bore (which provides 628N at 0.5MPa) if your force requirements are lower. The 12mm rod and M10x1.25 thread provide adequate rigidity for standard loads, but because the stroke is 160mm, ensure your mounting arrangement handles any potential side loading. The SAIJ series uses a specific mounting subset including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR brackets. For a dimensionally interchangeable ISO 15552 replacement, match the 32mm bore, 160mm nominal stroke, 75mm adjustment, PT tapered ports, and standard non-magnet configuration. If the application requires load holding without continuous air pressure, look to the SAIL or BSAI series instead, as this rear adjuster is not a lock.
Quick checklist
At the maximum 1.0MPa pressure, it delivers up to 801N (82kgf) of push force.
The rear adjuster screw allows you to mechanically shorten the effective stroke from its 160mm nominal length by up to 75mm, providing an adjustable travel window between 85mm and 160mm. It functions as a physical stop and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.