
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX170-100S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 170mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X170-100-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a nominal 170 mm stroke that can be dialed back by up to 100 mm, yielding a highly flexible 70-170 mm usable travel window for precise end-position tuning at commissioning.
This adjustable-stroke design eliminates the need to swap cylinders or bolt on external stops during product changeovers. The rear screw acts purely as a travel stop and works in tandem with the standard variable air cushions to decelerate the load, but it does not hold the load without live air. For position holding without pneumatic pressure, an external rod lock or a related SAIL pneumatic lock cylinder is required.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX170-100S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 70-170 mm travel window during format size changes on a packaging line without physically replacing the actuator.
Fine-tune the retract position during machine commissioning to perfectly seat delicate components without adding external stops.
Adjust the effective stroke on automated test fixtures to accommodate multiple part lengths within the 100 mm trim range.
If your setup demands less fine-tuning and a shorter fixed travel, stepping down to a standard SAI cylinder avoids the adjuster mechanism entirely.
Because this model features a 170 mm stroke, the 12 mm rod diameter and M10x1.25 rod thread handle moderate side loads, but any long unsupported overhang should still be guided externally. The PT tapered port threads ensure a robust pneumatic seal, and the integrated magnet allows direct mounting of CMSE reed or DMSE electronic solid-state switches along the dual sensor grooves. Mounting options are limited to the SAIJ subset: Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR brackets found on other variants.
Quick checklist
If pressure is increased to 0.9 MPa, the push force reaches 724 N.
The rear adjuster screw allows you to shorten the effective travel from the nominal 170 mm down by up to 100 mm, creating a 70-170 mm usable window. The adjuster is a mechanical stop that sets the end position and relies on the air cushion for deceleration; it does not lock the load in place without air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.