
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX180-10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 180mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X180-10-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a 170-180 mm usable travel window, allowing you to dial back the 180 mm nominal stroke by up to 10 mm during commissioning. The extruded aluminum barrel includes sensor grooves on both sides, and the -S magnet supports CMSE reed and DMSE electronic switches for precise position feedback.
This model uses a SUS420J2 stainless steel rod (option A) for improved corrosion resistance and features PT tapered port threads. The rear adjuster acts purely as a mechanical stop to set the retract end position; it does not lock the load or hold position without live air pressure. For load-holding requirements without continuous air, consider an external pilot-operated check valve or the SAIL lock series.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX180-10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Fine-tune the 170-180 mm travel window during initial commissioning to perfectly align a pushing face without machining external stopper blocks.
Quickly adjust the retract end-position by up to 10 mm on a packaging line when switching between slightly different product sizes.
If your setup needs less force, a smaller bore is preferable, while heavier loads require stepping up to the 40 mm bore, which provides 628 N. The adjustable stroke is ideal for product changeovers where exact end-stops vary slightly, eliminating the need to physically swap cylinders or bolt on external stopper blocks.
To match this ISO 15552 replacement, verify the 32 mm bore, 180 mm stroke, 10 mm adjustment range, PT port threads, and the -S magnet option. The 12 mm rod and M10x1.25 thread handle moderate side loads, but for any stroke of 300 mm or more, an external guide is recommended to prevent rod bending. SAIJ supports a reduced mounting set: Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
A rear adjusting screw acts as a mechanical stop, allowing you to shorten the 180 mm nominal stroke by up to 10 mm, creating a 170-180 mm usable travel window. It only sets the end position and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.