
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX180-50 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 180mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X180-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a nominal 180 mm stroke with an adjustment range of up to 50 mm, creating a 130-180 mm usable travel window for precise end-position tuning during commissioning. In this configuration, the piston rod uses SUS420J2 stainless steel (code A) for improved corrosion resistance, and ports feature PT tapered threads.
The rear adjuster acts strictly as a travel stop for deceleration and positioning; it is not a lock. For applications requiring load-holding without live air pressure, consider the SAIL or BSAI series, or an external pilot-operated check valve.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX180-50 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract position within the 130-180 mm window during product line changeovers without installing external physical stops or swapping cylinders.
Ideal for assembly stations where the end-of-stroke position needs precise mechanical tuning to accommodate varying component heights or sensor targets.
Provides 402 N of clamping thrust at 0.5 MPa, with the rear stopper allowing operators to set the exact clamping travel distance to prevent over-travel.
Conversely, if you require less force, you would step down to a smaller bore. The SAIJ32X180-50 is selected over a fixed-stroke SAI cylinder when machine setups require frequent product changeovers or fine-tuning of the retract position without swapping out the physical actuator.
When replacing an ISO 15552 cylinder, verify the 32 mm bore, 180 mm stroke, 50 mm adjustment range, PT port threads, and the SUS420J2 stainless steel rod material. The SAIJ mounting interface supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 brackets, omitting FB, CA, CB, and CR options. Because the stroke is under 300 mm, side-load concerns are minimal, but ensure the 12 mm rod and M10x1.25 thread are aligned to prevent premature seal wear.
Quick checklist
The rear adjusting screw acts as an external stopper that shortens the effective stroke by up to 50 mm. For this model, it creates a usable travel window of 130 to 180 mm, allowing you to fine-tune the retract end-position at commissioning without changing the cylinder itself.
At the maximum pressure of 1.0 MPa, it can deliver up to 82 kgf of push force.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.