
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X130-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 130mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X130-75 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a nominal 130 mm stroke with a 75 mm adjustment range, yielding a highly flexible usable travel window of 55 to 130 mm.
The rear adjustment screw acts purely as a travel stop to fine-tune the retract end position during commissioning; it does not lock or hold the load without live air pressure. This model features a carbon steel piston rod, a G1/8 PT port, and 27 mm variable air cushions at both ends. It supports AirTAC CMSE reed and DMSE electronic sensors via the dual-side extruded barrel grooves when a magnet is specified.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X130-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 130 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×130 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract position on the fly when switching between product sizes, using the 55-130 mm travel window to avoid repositioning physical hard stops.
Fine-tune the final end-of-stroke position during commissioning to absorb mechanical tolerances, relying on the rear screw rather than adding shims.
Adjust the effective stroke dynamically on an assembly line to press or locate parts at varying depths without replacing the entire actuator.
If your setup demands higher thrust, stepping up to the 40 mm bore yields 628 N at the same pressure. The 75 mm adjustment range allows you to dial back the stroke by up to 75 mm without swapping the cylinder or adding external stops. For exact ISO 15552 replacement matching, verify the 130 mm stroke, 75 mm adjuster, G1/8 PT port, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the rear adjuster is a stop, not a lock; for fail-safe load holding without live air, consider the SAIL or BSAI series. Because the 130 mm stroke is under 300 mm, side-load stress on the 12 mm rod is manageable, though external guides are still recommended for heavy lateral loads.
Quick checklist
The rear adjuster screw allows you to shorten the effective stroke by up to 75 mm from its 130 mm nominal length, creating a usable travel window of 55 to 130 mm. It functions as a mechanical stop to set the end position and does not hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.