
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X140-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 140mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X140-50-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, allowing you to dial back the 140 mm nominal stroke by up to 50 mm. This creates a 90-140 mm usable travel window, enabling precise end-position tuning at commissioning without swapping the cylinder or bolting on external stops. It features a standard carbon steel piston rod and a PT tapered port thread.
The rear adjuster acts purely as a mechanical stop to set the travel end and must not be confused with a lock, as the cylinder cannot hold a load without live air pressure. It supports a reduced SAIJ mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X140-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 140 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×140 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 90-140 mm travel window during product size changeovers without swapping out the entire cylinder assembly.
Fine-tune the final retract position at commissioning using the rear screw, eliminating the need for external mechanical stops.
Utilize the -S magnetic piston with DMSE electronic or CMSE reed switches in the dual-side barrel grooves for precise position feedback.
Choose this 32 mm bore adjustable-stroke cylinder when your application requires variable end stops or frequent machine changeovers, stepping down from a 40 mm bore (which provides 628 N at 0.5 MPa) if your force requirements are modest. The integrated 50 mm adjustment window is perfect for fine-tuning product-size changes on a line without replacing the actuator. If you need to step up force significantly, consider a 50 mm bore offering 982 N at 0.5 MPa.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 140 mm stroke, 50 mm adjustment range, PT port thread, and required mounting accessories. Because the stroke is 140 mm, side loads are minimal, but always ensure proper alignment. For load-holding without live pressure, the SAIJ adjuster will not suffice; consider an AirTAC SAIL or BSAI series instead.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 82 kgf.
The rear adjusting screw allows you to shorten the 140 mm nominal stroke by up to 50 mm, creating a 90-140 mm usable travel window. The adjuster acts as a mechanical stop to set the end position and is not a lock, meaning the cylinder requires live air to hold a load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.