
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X165-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 165mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X165-40-S is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear stroke adjuster. With a nominal 165 mm stroke and a 40 mm adjustment range, it provides a usable travel window of 125 to 165 mm. This built-in adjuster allows you to dial in the exact retract end-position at commissioning without adding external stops or swapping the cylinder.
The extruded aluminum barrel includes sensor grooves on both sides, and this -S variant includes a magnet for CMSE reed and DMSE electronic solid-state switches. The 12 mm carbon steel rod and M10x1.25 thread handle moderate side loads, while the SAIJ mounting set supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 attachments. Note that the rear adjuster acts as a travel stop, not a lock; it will not hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X165-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 125 to 165 mm retract position during product size changes without physically replacing the cylinder or reworking the fixture.
Fine-tune the final resting position during commissioning using the 40 mm rear adjuster, eliminating the need to add external mechanical stops.
If you need less force, a smaller bore is advised, but if your machine changeover demands variable end-stops, this adjustable-stroke model is far more efficient than a fixed-stroke SAI cylinder. The PT tapered port threads match standard pneumatic fittings, and the -S magnet enables position sensing.
Because the stroke is 165 mm, the 12 mm rod is adequately supported, but always guide the load to prevent side-load damage. If your process requires the cylinder to hold its position without continuous air pressure, the SAIJ rear adjuster will not suffice; consider an external rod lock, a pilot-operated check valve, or AirTAC SAIL and BSAI locking cylinders instead.
Quick checklist
At the maximum 1.0 MPa, it can deliver up to 82 kgf.
The rear adjuster acts as an external mechanical stop that lets you shorten the effective stroke from 165 mm down to as little as 125 mm. It is a travel stop for fine-tuning, not a lock, and cannot hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.