
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X170-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 170mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X170-100 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the travel window between 70 and 170 mm. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE and DMSE switches.
Equipped with a 12 mm carbon steel rod and an M10x1.25 thread, this unit handles moderate side loads while providing secure mechanical attachment. It uses a PT tapered G1/8 port and relies on adjustable air cushions at both ends to decelerate the payload smoothly. The rear stopper mechanism sets the end position without locking the load, meaning live air pressure is required to hold position.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X170-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 70 to 170 mm travel during commissioning to perfectly time the end-of-stroke position without machining new hard stops.
Quickly adjust the effective stroke on packaging lines when running slightly different carton lengths, minimizing downtime between batches.
Use the wide 100 mm adjustment window on test rigs to empirically find the optimal travel distance before finalizing a fixed-stroke SAI cylinder design.
The 100 mm adjustment range is ideal for prototyping or lines running multiple product sizes, allowing you to dial in the exact 70-170 mm travel without swapping the cylinder or adding external stops. Since the 170 mm stroke is below the 300 mm threshold, external side-load guides are less critical, but the 12 mm rod still requires reasonably good alignment to prevent premature seal wear.
For load-holding without continuous air pressure, this standard adjustable cylinder is not a lock; you would need to specify a SAIL or BSAI variant instead. To match this ISO 15552 interchangeable cylinder for replacement, verify the 32 mm bore, 170 mm nominal stroke, 100 mm adjustment range, PT G1/8 port, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). No magnet is specified for this configuration.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 801 N (82 kgf) of push force.
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective travel from the 170 mm nominal stroke down to as little as 70 mm. It only sets the end position and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.