
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X170-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 170mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X170-75-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster, providing a highly flexible usable travel window of 95 to 170 mm. The integrated -S magnet enables direct mounting of CMSE reed and DMSE electronic solid-state sensors directly into the dual-side barrel grooves.
This adjustable variant allows you to dial in the exact retract end-position during commissioning or product changeover without swapping out the cylinder or adding external stops. The rear adjuster acts purely as a mechanical stop to set the travel limit; it does not hold the load without live air pressure. For applications requiring true load-holding without continuous air, consider the SAIL or BSAI series instead.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X170-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 95 to 170 mm retract position during initial machine commissioning without physically swapping out the cylinder.
Quickly adapt the stroke window on production lines running varying product sizes by adjusting the rear stopper up to 75 mm.
Provide a mechanical stop to fine-tune the end-of-stroke deceleration point for delicate picking and placing tasks.
If your setup demands higher thrust, stepping up to the 40 mm bore yields 628 N at 0.5 MPa. The 75 mm adjustment range is particularly useful for prototyping or machinery that processes varying product sizes, allowing you to fine-tune the 170 mm nominal stroke on the fly rather than relying on a fixed SAI cylinder.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 170 mm stroke, 75 mm adjustment, PT port thread, and -S magnet requirement. The SAIJ utilizes a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR brackets. Note that the 12 mm carbon steel rod and M10x1.25 thread handle moderate side loads well, but long unsupported strokes still require an external guide.
Quick checklist
At 0.9 MPa, the push force increases to 724 N.
The rear adjuster screw lets you mechanically shorten the 170 mm nominal stroke by up to 75 mm, creating a usable travel window of 95 to 170 mm. This stopper only sets the end position; it does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.