
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X175-10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 175mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X175-10-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, enabling you to dial back the nominal 175 mm travel by up to 10 mm. This yields a precise 165-175 mm usable window, allowing you to fine-tune the retract end position at commissioning without physically swapping the barrel or adding external stops.
This variant features a carbon steel rod with an M10x1.25 thread and PT tapered ports. The extruded aluminum barrel includes sensor grooves on both sides, and because this is the -S magnet version, it is fully compatible with AirTAC CMSE reed and DMSE electronic solid-state switches for precise position feedback. The rear adjuster acts purely as a travel stop to set the end position, so it will not hold a load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X175-10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 165-175 mm end-stop during product size changes on a packaging line without swapping out the entire cylinder assembly.
Fine-tune the retract position at commissioning to compensate for mechanical tolerances, using the rear screw rather than adding external shims.
The 10 mm adjustable stroke is specifically valuable for machine setups requiring variable end-stops or product-size changeovers, offering more flexibility than a fixed-stroke SAI cylinder. To match this ISO 15552 interchangeable replacement, specify a 32 mm bore, 175 mm stroke, 10 mm adjustment, PT port thread, and the -S magnet option.
Because the 175 mm stroke is relatively long for the 12 mm rod diameter, an external guide rail is recommended to prevent excessive side-load wear on the rod seals. Remember that the rear adjuster and air cushions only decelerate the travel end; for load-holding without live air pressure, you must integrate an external rod lock or pilot-operated check valve. SAIJ supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
It operates at speeds between 30 and 800 mm/s, supported by 27 mm air cushions at both ends.
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective travel from the 175 mm nominal stroke down to as little as 165 mm. This creates a 165-175 mm usable window for fine-tuning the retract end position without changing the cylinder itself.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.