
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X175-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 175mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X175-50-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a 125-175 mm usable travel window, allowing you to dial back the 175 mm nominal stroke by up to 50 mm during commissioning. The carbon steel rod and M10x1.25 thread handle standard side loads, while the extruded aluminum barrel integrates dual sensor grooves.
Equipped with a magnetic piston (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The rear adjuster acts purely as a mechanical stop to fine-tune the retract position without adding external stops. It utilizes a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and PT tapered ports, omitting the FB, CA, CB, and CR options found on some standard ISO blocks.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X175-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 125-175 mm travel window during product size changes without physically replacing the cylinder or bolting on external stops.
Use the 50 mm rear adjustment screw to fine-tune the retract position at commissioning, hitting exact mechanical endpoints for delicate pick-and-place tasks.
The 50 mm adjustment window is ideal for product changeovers on a line, letting you reposition the retract end-stop without swapping the cylinder. If your setup needs less than 125 mm of travel, step down to a shorter standard stroke. For higher force demands up to 628 N, step up to the 40 mm bore.
Because the rear adjuster and air cushions only decelerate the travel end, this cylinder does not hold the load without live air pressure. For fail-safe load holding, consider the SAIL (air-released lock) or BSAI (clamp-lock) series. This SAIJ32X175-50-S is dimensionally interchangeable per ISO 15552, featuring a PT port, the specified mounting options, and a magnetic piston for CMSE/DMSE switches.
Quick checklist
It operates at a speed range of 30-800 mm/s and features a maximum operating pressure of 1.0 MPa.
The rear adjuster acts as a mechanical stop that lets you shorten the 175 mm nominal stroke by up to 50 mm, creating a 125-175 mm usable travel window. It sets the retract end position during commissioning but does not lock or hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.