
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X195-20 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 195mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X195-20 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a 195mm nominal stroke that can be fine-tuned backward by up to 20mm, creating a usable 175-195mm travel window. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch placement.
Unlike a fixed-stroke SAI cylinder, this model allows precise end-position tuning at commissioning without adding external stops. The PT tapered port (G1/8) and M10x1.25 rod thread provide standard pneumatic connections. The rear adjuster acts purely as a travel stop and does not hold the load without live air pressure. For position holding without continuous air, consider the SAIL or BSAI series.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X195-20 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 195 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×195 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 175-195mm travel window during product size changes without swapping the cylinder or bolting on external stops.
Fine-tune the retract end-position at startup to compensate for mechanical tolerance variations in the fixture.
If your setup needs less force, stepping down is not an option below 32mm in this series, but stepping up to the 40mm bore yields 628N. The adjustable stroke is ideal for machine changeovers where the exact 175-195mm travel window must be dialed in on-site. Since the stroke is 195mm, an external guide is recommended to prevent side-load wear on the 12mm carbon steel rod.
When replacing an ISO 15552 cylinder, match the 32mm bore, 195mm stroke, 20mm adjustment range, PT port thread, and standard carbon steel rod. The SAIJ mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2 options, omitting FB, CA, CB, and CR. This cylinder uses variable air cushions at both ends to decelerate the piston, but it is not a locking device.
Quick checklist
At 0.9MPa, the push force increases to 724N.
A rear adjusting screw acts as a mechanical stopper, allowing you to shorten the effective stroke from the nominal 195mm down to 175mm. This adjuster sets the travel end and requires live air pressure to hold the load; it is not a locking brake.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.