
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X200-20S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 200mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X200-20-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a carbon steel piston rod and a built-in magnet for position sensing. By turning the external adjustment screw, you can shorten the effective travel, providing a usable stroke window of 180 to 200 mm without changing the physical cylinder mounting.
The extruded aluminum barrel includes sensor grooves on both sides, allowing you to easily mount CMSE reed or DMSE electronic switches exactly where needed. The rear adjuster acts purely as a travel stop to set the retract distance, so it will not hold a load safely without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X200-20S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract distance within the 180-200 mm window during product size changes without physically swapping cylinders or adding external stopper blocks.
Set precise retract positions for diverters or gating mechanisms on a conveyor line, adjusting the travel by up to 20 mm as needed.
If your setup demands less force, stepping down is an option, but if you need significantly higher thrust, consider a 40 mm bore which provides 628 N at the same pressure. The adjustable-stroke design is selected over a fixed-stroke SAI cylinder when you need to fine-tune the retract position during machine setup or product changeover rather than relying on external stops.
For ISO 15552 replacement, match the 32 mm bore, 200 mm nominal stroke, 20 mm adjustment range, PT tapered port thread, and the -S magnet option. The SAIJ series supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR foot and pivot brackets. Because the nominal stroke is 200 mm, side-loading is minimal, but for any travel exceeding 300 mm, an external guide rail is recommended to protect the 12 mm rod. Note that for load-holding without live air, you must use a SAIL or BSAI cylinder instead of relying on this adjuster.
Quick checklist
The rear adjustment screw acts as a mechanical stop that lets you shorten the nominal 200 mm stroke by up to 20 mm, giving a usable travel window of 180 to 200 mm. This allows you to fine-tune the end position at commissioning without replacing the cylinder.
The maximum thrust is 82 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.