
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X200-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 200mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X200-75 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to trim the effective travel back by up to 75 mm. This creates a highly versatile usable stroke window from 125 to 200 mm, letting you dial in the exact end position during commissioning without adding bulky external stops.
Because the rear adjuster acts purely as a mechanical stop, it does not hold the load if air pressure drops; for true fail-safe load holding, consider the SAIL or BSAI series. This 32 mm bore model uses a PT G1/8 port and features variable air cushions at both ends to decelerate the moving piston. The extruded aluminum barrel includes sensor grooves on both sides, ready to accept AirTAC CMSE reed or DMSE electronic solid-state switches if you add a magnet later.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X200-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the retract stroke by up to 75 mm during product size changes without physically swapping the cylinder or repositioning external stop blocks.
Fine-tune the exact end-of-stroke position at commissioning to compensate for mechanical tolerances in a new fixture or assembly press.
Adjust the travel window between 125 and 200 mm to test multiple sensor trigger points or clamping depths on a single test rig.
Choose this SAIJ32X200-75 when your machine setup requires frequent product changeovers or precise variable end-stops within a 125 to 200 mm travel window. The integrated rear screw stopper simplifies fine-tuning at commissioning compared to a fixed-stroke SAI cylinder, which would require physical shimming or swapping components to alter the travel. If your application needs less force, stepping down is not an option in this size range, but if you need significantly more thrust, a 40 mm bore provides 528 N of pull force at 0.5 MPa.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 200 mm nominal stroke, 75 mm adjustment range, PT G1/8 port, and your required mounting bracket from the SAIJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). Since this unit has a 200 mm stroke, ensure proper guidance to prevent excessive side loads on the 12 mm piston rod, as long unsupported strokes can cause premature seal wear.
Quick checklist
It can reach a maximum thrust of 82 kgf at 1.0 MPa.
The rear adjuster screw acts as a mechanical stop that lets you shorten the 200 mm nominal stroke by up to 75 mm, providing an effective travel window of 125 to 200 mm. It only sets the end position and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.