
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X220-10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 220mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X220-10-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a 32mm bore, a PT tapered port, and a carbon steel piston rod. By integrating an external adjusting screw, this model provides a usable travel window of 210-220mm from its 220mm nominal stroke, allowing you to dial back the extension by up to 10mm during commissioning.
This adjustable-stroke design eliminates the need to swap cylinders or bolt on external stops when fine-tuning end positions. The rear adjuster acts purely as a travel stop for deceleration alongside the variable air cushions, meaning it does not hold the load without live air. For load-holding without pressure, consider the SAIL or BSAI series. The extruded aluminum barrel includes sensor grooves on both sides, and the mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X220-10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 220 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×220 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 210-220mm stroke window during product size changes without swapping out the entire cylinder assembly.
Use the 10mm rear adjustment screw to fine-tune the exact end position during machine commissioning.
If your setup demands greater thrust, stepping up to the 40mm bore yields 628N. The SAIJ32X220-10-S is chosen over a fixed-stroke SAI cylinder when you need a 210-220mm adjustable window to accommodate product changeovers or minor machine setup variations. To ensure proper ISO 15552 replacement matching, verify the 220mm stroke, 10mm adjustment, PT port, and the -S magnet requirement.
Because this unit features a 220mm stroke, the 12mm carbon steel rod and M10x1.25 thread provide adequate support, but long unsupported strokes still benefit from an external guide to manage side loads. The standard speed range of 30-800mm/s suits most handling tasks. Remember that the rear adjuster and air cushions only manage travel end deceleration; they do not function as a brake or lock.
Quick checklist
At 0.7 MPa, the push force increases to 563N.
The rear adjuster screw allows you to shorten the effective travel from the 220mm nominal stroke down to 210mm, creating a 210-220mm usable window. This stop only sets the travel end and does not lock or hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.