
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X250-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 250mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X250-40-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a 32mm bore and a 250mm nominal stroke that can be fine-tuned down by up to 40mm, giving you a precise 210-250mm usable travel window during commissioning.
This adjustable-stop design eliminates the need to swap cylinders or bolt on external stops when dialing in end positions. The extruded aluminum barrel includes sensor grooves on both sides, and because this SKU includes a magnet (-S), it directly supports AirTAC CMSE reed and DMSE electronic solid-state switches. The rear adjuster acts purely as a travel stop and does not hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X250-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 210-250mm travel window during product size changeovers without swapping out the entire cylinder or adding external mechanical stops.
Use the rear adjuster to fine-tune the retract stroke on automated test fixtures, ensuring precise end-position tuning at commissioning.
If you need significantly more thrust, stepping up to the 40mm bore yields 628N at the same pressure. The SAIJ32X250-40-S is selected over a fixed SAI model when you need a variable end-stop to accommodate product changeovers without machining new mountings.
Because this unit features a 250mm stroke, the 12mm carbon steel rod and M10x1.25 thread handle moderate side loads, but long unsupported strokes still require an external guide to prevent rod wear. For load-holding without continuous air pressure, this cylinder is not a lock; you would need to specify a SAIL or BSAI series instead. It uses the reduced SAIJ mounting set: Basic, FA, LB, TC, FTC, TCM1, TCM2, omitting FB, CA, CB, and CR.
Quick checklist
The rear adjusting screw lets you shorten the effective stroke by up to 40mm. This turns the standard 250mm stroke into a 210-250mm adjustable travel window, allowing you to fine-tune the retract end position at commissioning without adding external stops.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.