
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X280-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 280mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X280-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a nominal 280 mm stroke that can be dialed back by up to 75 mm, yielding a usable travel window of 205 to 280 mm for precise end-position tuning. The unit uses a 12 mm carbon steel rod with an M10x1.25 thread, and its extruded aluminum barrel includes sensor grooves on both sides.
This adjustable model uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. The rear adjuster acts strictly as a travel stop to fine-tune the retract position during commissioning or product changeover without adding external stops. It is not a lock; the cylinder will not hold a load without live air pressure. For load-holding requirements, consider the SAIL or BSAI series instead.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X280-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract end-position from 205 to 280 mm during product size transitions without swapping cylinders or adding external mechanical stops.
Adjust the stroke on the fly for a conveyor diverter arm that needs to accommodate different package widths on the same line.
The adjustable stroke is ideal for machine setups that undergo frequent product-size changeovers, eliminating the need to swap out a fixed-stroke SAI cylinder. Because the 280 mm stroke is relatively long for this small 12 mm rod diameter, an external guide is recommended to prevent excessive side-loading and premature seal wear.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 280 mm stroke, 75 mm adjustment range, PT tapered port threads, and the specified mounting bracket. This unit lacks a magnet, so it does not support CMSE or DMSE sensors; if position detection is needed, select an -S model. The standard speed range is 30-800 mm/s, controlled via variable air cushions at both ends.
Quick checklist
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective stroke by up to 75 mm. This provides a usable travel window of 205 to 280 mm, allowing you to fine-tune the end position at commissioning without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.