
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X300-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 300mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X300-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a nominal 300 mm travel that can be dialed back by up to 75 mm, yielding a highly flexible 225 to 300 mm usable stroke window for precise end-position tuning.
This adjustable-stop design allows you to fine-tune the retract end-position at commissioning or during product changeovers without swapping the cylinder or adding external stops. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE reed and DMSE electronic switches. The rear adjuster acts purely as a travel stop and works with the variable air cushion to decelerate the load, but it does not hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X300-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly dial in the retract position from 300 mm down to 225 mm using the rear stopper screw to accommodate different product lengths on the same conveyor line.
Fine-tune the end-of-stroke position during initial setup without machining external stop blocks or changing out the entire ISO 15552 cylinder body.
If your setup demands higher thrust, stepping up to the 40 mm bore yields 628 N at the same pressure. Selecting the SAIJ adjustable version over a fixed-stroke SAI cylinder is ideal when you need a variable end-stop to accommodate multiple product sizes on a single line. To replace an ISO 15552 cylinder, match the 32 mm bore, 300 mm stroke, PT port thread, and desired mounting accessory from the SAIJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Because the 300 mm stroke is relatively long for a 32 mm bore, the 12 mm diameter rod and M10x1.25 thread will be subjected to higher side loads if the tooling is unsupported. For this configuration, adding an external guide is strongly recommended to prevent rod binding and premature seal wear. For load-holding requirements without live air, note that this cylinder's adjuster is only a stop; consider an AirTAC SAIL or BSAI series instead.
Quick checklist
It can reach a maximum thrust of 82 kgf at 1.0 MPa.
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective travel from its 300 mm nominal stroke down to 225 mm. This provides a 75 mm adjustment window for fine-tuning the retract end position, but it functions as a stop, not a lock, and cannot hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.