
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X325-100S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 325mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X325-100-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear mechanical stroke adjuster. Because this SKU carries the -S option, it includes a magnet for position sensing via CMSE reed or DMSE electronic solid-state switches mounted in the dual-side sensor grooves.
The 100mm adjustment code creates a highly flexible usable travel window from 225 to 325mm. This allows you to dial in the exact retract end-position during commissioning or product changeover without adding external stops. The rear adjuster acts purely as a travel stop to set deceleration and end-position, not as a lock; it will not hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X325-100S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Rapidly adapt packaging lines to different carton sizes by dialing the rear stopper back from 325 to 225mm without changing hardware.
Fine-tune the retract end-position during initial commissioning to perfectly time the 12mm rod extension against mechanical stops.
Use the 100mm travel window to test multiple extension lengths in a prototype jig before locking in a final fixed-stroke SAI cylinder.
Select the adjustable SAIJ over a fixed-stroke SAI when a machine setup demands fine end-position tuning across different product sizes. For load-holding without continuous air pressure, this cylinder is insufficient—consider the SAIL (air-released lock) or BSAI (clamp-lock) series instead.
When configuring your ISO 15552 replacement, verify the 325mm stroke, 100mm adjustment range, PT tapered port (G1/8), and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2—omitting FB, CA, CB, and CR). Because the 325mm stroke is relatively long for a 32mm rod, long unsupported strokes still need an external guide to prevent excessive side-loading and premature seal wear.
Quick checklist
At the maximum 1.0 MPa pressure, it delivers up to 82 kgf.
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective stroke from its 325mm nominal length down to a minimum of 225mm. It sets the travel end and deceleration point but does not lock or hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.