
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X325-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 325mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X325-75-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a 325 mm nominal stroke that can be dialed back by up to 75 mm, yielding a precise 250-325 mm usable travel window for on-the-fly end-position tuning.
This variant includes a built-in magnet for position sensing with CMSE reed or DMSE electronic switches. The extruded aluminum barrel incorporates sensor grooves on both sides for flexible mounting. Because the 325 mm stroke is relatively long for a 32 mm bore, an external guide is recommended to handle side loads and prevent rod binding.
The selection criteria for this cylinder center on its ability to fine-tune the retract end position during commissioning without swapping components or adding external stops. If your application requires less force, stepping down is not an option at this bore size, but stepping up to a 40 mm bore increases push force to 628 N at 0.5 MPa. The rear adjuster acts strictly as a travel stop and does not hold the load without live air; for dead-air load holding, consider the SAIL or BSAI series. To match this ISO 15552 dimensionally interchangeable cylinder, specify the 32 mm bore, 325 mm stroke, 75 mm adjustment, PT port, and -S magnet.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X325-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract distance between 250 and 325 mm during machine setup to accommodate different product sizes without external stops.
Quickly adjust the stroke window on a packaging line to handle varying carton lengths, reducing downtime between production runs.
Fine-tune the clamping position on a machining fixture where the exact end-of-travel point must be calibrated to the workpiece.
Choose the SAIJ32X325-75-S when you need variable end-stops for product changeovers on a packaging line. The 75 mm adjustment window allows operators to dial in the exact 250-325 mm retract distance without changing the cylinder. Remember that the rear adjuster is a stop, not a lock; it cannot hold loads without continuous air pressure. Use the SAIL or BSAI series if dead-air locking is required. This cylinder uses the standard SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets.
Quick checklist
At the maximum 1.0 MPa pressure, it delivers up to 82 kgf.
The rear adjuster screw allows you to shorten the effective stroke by up to 75 mm from the 325 mm nominal length, creating a 250-325 mm travel window. It functions as a mechanical stop to fine-tune the end position and is not a locking device.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.