
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X375-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 375mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X375-75 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a nominal 375 mm stroke that can be fine-tuned backward by up to 75 mm, yielding a usable travel window between 300 and 375 mm.
Because the adjustment mechanism acts purely as a mechanical stop at the retract end, it decelerates the piston alongside the built-in air cushions but does not lock the load without continuous air pressure. The extruded aluminum barrel features sensor grooves on both sides, allowing you to mount CMSE reed or DMSE electronic switches if position feedback is needed later.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X375-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 375 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×375 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 300-375 mm retract end-stop during product size changes without swapping the actuator or reworking the fixture.
Fine-tune the final resting position of a tooling plate by up to 75 mm during commissioning to achieve perfect alignment.
Adjust the pusher travel window on the fly to accommodate different package lengths moving down a packaging line.
Choose this adjustable-stroke model when your assembly requires variable end-stops or frequent product changeovers, eliminating the need to physically swap cylinders or bolt on external stopper blocks. If your application demands greater thrust, stepping up to the 40 mm bore increases push force to 628 N at 0.5 MPa; conversely, lighter duties can use smaller bores. For load-holding without live air pressure, a standard SAIJ is insufficient—you must specify a SAIL pneumatic lock or an external rod lock.
To match this ISO 15552 dimensionally interchangeable cylinder, confirm the 32 mm bore, 375 mm stroke, 75 mm adjustment range, PT G1/8 port, and carbon steel rod. With a 375 mm stroke, the 12 mm rod is susceptible to side-loading; ensure you use an external guide to prevent binding and premature seal wear. SAIJ supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, omitting FB, CA, CB, and CR.
Quick checklist
The rear adjuster screw acts as a mechanical stop, allowing you to shorten the effective stroke from 375 mm down to a minimum of 300 mm. It sets the travel end and relies on the air cushion for deceleration, but it does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.