
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X425-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 425mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X425-30 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a 425 mm nominal stroke that can be fine-tuned down by up to 30 mm, yielding a usable travel window of 395-425 mm. This allows precise end-position calibration during commissioning without adding external stops.
Equipped with a 12 mm carbon steel rod and M10x1.25 thread, this model handles standard loads within its force class. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch mounting. It uses a PT tapered port thread (G1/8) and operates at speeds between 30 and 800 mm/s. The rear screw acts purely as a travel stop for deceleration and positioning, not as a lock to hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X425-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 395-425 mm end position precisely during product size changes without replacing the cylinder or adding shims.
Fine-tune the retract stop during commissioning to achieve exact pressing or clamping depth on automated lines.
Accommodate slight variations in incoming part lengths by adjusting the rear stopper within the 30 mm window.
Choose this 32 mm bore when an application requires precise mechanical end-stop tuning within a 395-425 mm travel range. If your setup needs greater thrust, stepping up to the 40 mm bore increases push force to 628 N at 0.5 MPa. Because the 425 mm stroke is relatively long for a 32 mm bore, an external guide is recommended to prevent excessive rod side-loading and premature seal wear.
The adjustable stroke is ideal for product changeovers where the exact end position varies slightly, eliminating the need to swap out a fixed-stroke SAI cylinder. For direct compatibility, match the 32 mm bore, 425 mm stroke, 30 mm adjustment, PT G1/8 port, and desired mounting style. SAIJ supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, deliberately omitting FB, CA, CB, and CR options. If your circuit requires true load-holding without continuous air pressure, consider the SAIL or BSAI series instead of relying on the adjuster.
Quick checklist
At the maximum 1.0 MPa pressure, it achieves 82 kgf.
The rear adjuster screw allows you to shorten the 425 mm nominal stroke by up to 30 mm, creating a usable travel window of 395-425 mm. This stopper sets the end position but does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.