
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X425-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 425mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X425-40-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a carbon steel rod and a PT tapered port. Because of the 40mm adjustment range, the usable travel window spans from 385mm to 425mm, allowing precise end-position tuning without external stops. With a 12mm rod and M10x1.25 thread, it handles moderate side loads effectively.
The -S magnet option enables direct mounting of CMSE reed or DMSE electronic solid-state sensors along the dual-sided barrel grooves. The rear adjuster acts strictly as a travel stop for deceleration setup, not a lock, and the standard air cushions help absorb end-of-stroke impact.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X425-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 385-425mm end position during line changeovers without machining new hard stops or replacing the cylinder.
Adjust the retract distance on the fly to accommodate different package sizes moving down a packaging conveyor line.
Use the 40mm rear stopper screw to resolve minor mechanical timing variances and perfect end-of-stroke deceleration at startup.
Select this 32mm bore model when an application requires a 425mm stroke but needs flexibility during commissioning or product changeover, trimming back up to 40mm without swapping cylinders. The SAIJ mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR options.
Because the 425mm stroke is relatively long for a 32mm bore, an external guide is recommended to prevent rod deflection and premature seal wear. For any load-holding requirements without continuous live air pressure, note that this cylinder cannot hold its position; you should consider the SAIL (air-released lock) or BSAI (clamp-lock) variants instead.
Quick checklist
The 40mm rear adjuster screw lets you mechanically shorten the effective travel from 425mm down to 385mm. This creates a 385-425mm usable window, allowing you to set the exact retract end-position during commissioning without adding external stops.
At the maximum 1.0MPa pressure, the push force reaches 801N.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.