
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32X425-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 425mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X425-75-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. The integrated magnet (-S) supports position sensing via AirTAC CMSE reed and DMSE electronic solid-state switches housed in the dual-side barrel grooves.
Because the stroke exceeds 300mm, the 12mm carbon steel rod and M10x1.25 thread require careful alignment to manage side loads, making an external guide advisable for unsupported lengths. The rear stopper lets you dial in the retract end-position during commissioning without adding external stops. Note that this adjuster acts purely as a travel stop and does not hold the load without live air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32X425-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 350-425mm travel window during product size changes without physically swapping the cylinder or adding external mechanical stops.
Provides a adjustable retract end-stop for sorting or pushing parts on a conveyor where the target position shifts between production runs.
Allows technicians to precisely trim the final 75mm of stroke during machine setup to perfect timing and avoid mechanical interference.
The 75mm adjustment range is ideal for product-size changeovers on a line, allowing you to reposition the retract end-stop on the fly rather than swapping to a fixed-stroke SAI cylinder. For load-holding without continuous air pressure, this cylinder is insufficient—the rear adjuster is not a lock—so you would need to specify a SAIL or BSAI model instead.
To match this ISO 15552 dimensionally interchangeable cylinder, confirm the 425mm stroke, 75mm adjust code, PT tapered port thread, and your required mounting bracket from the reduced SAIJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2). FB, CA, CB, and CR mounts are omitted from this adjustable variant.
Quick checklist
At the maximum 1.0 MPa pressure, it delivers up to 82 kgf.
The rear adjuster screw acts as a mechanical stop, allowing you to shorten the effective stroke from its 425mm nominal length down to 350mm. It sets the travel end but does not lock or hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.